A fab cleaned the way your cleanroom manager writes it
Aeroso cleans semiconductor and electronics cleanrooms and the building around them: gowning and locker rooms, cleanroom bays, the corridors and service chases beside them, pass-throughs, and the offices, break rooms and restrooms where the people who run the tools spend the rest of their day. Your facility’s written protocol and your cleanroom manager set every step: the gowning order, the agent, the wipes, the wipe-down order, the frequency and what may come through the door.
Fab work adds production-floor detail to the routine on our cleanroom and laboratory cleaning page, which covers lab buildings and controlled rooms in general.
Semiconductor work around the Peninsula
Semiconductor fabs, clean assembly areas and nanofabrication labs are part of the Peninsula’s building mix.
Many of those buildings mix a fab or clean assembly area with ordinary offices under one roof, and a single plan covers both, each with its own method.
Reading the class on the door
Your facility classifies and tests the cleanroom’s air, and its suppliers set which agents suit each surface. Our crews use exactly what you specify, in the order your protocol sets.
Rooms in and around the cleanroom
| Area | What our crews clean, as the protocol directs |
|---|---|
| Locker and gowning rooms | Benches, lockers’ outer faces, mirrors and floors; tacky mats changed where your protocol lists it |
| Cleanroom bays | Ceiling surfaces, walls and windows, cleared tables and listed equipment surfaces, then the floor |
| Corridors and service chases | Floors and walls, with safety showers, eyewash stations and extinguishers kept clear |
| Pass-throughs | Wiped with the agent and in the sequence your protocol names |
| Offices, break rooms and restrooms | Our regular commercial routine, with separate tools and supplies |
Process tools stay with your staff. One published fab protocol, for example, requires a tool maintenance form filed by the tool owner and approved by EHS before anyone cleans a tool that holds hazardous production materials, and filters and facility systems are never on our route.
How a crew enters and what it leaves in the locker
People are the main source of particles in a cleanroom, so the way a crew enters matters as much as what it cleans. Gowning often starts in the locker room with safety glasses, shoe covers, a hair net, a face mask and gloves, and the cleanest rooms add a full gown put on from the top down and taken off in reverse.
Your protocol sets the sequence, from the shoe cleaner and tacky mat to the bench where garments go on from the dirty side to the clean side, and it lists what stays out, such as regular paper, cardboard, wooden-handled tools, aerosols or scented products, and how approved items and cart wheels are prepared before they go in.
Our crews follow your posted sequence. Phones and street items stay in the locker, only the tools and supplies your protocol lists go in, and each entry is planned to finish a full zone before the crew leaves.
The order of a wipe-down
A cleanroom wipe-down follows a set order. Work starts in the cleaner area farthest from the main pass-through and moves toward the exit, and within a room it goes from the ceiling to the walls and windows, then equipment and tables, and ends with the floor.
We run your version of that order. The crew uses your agent and wipes, moves slowly without sliding anything across floors or cabinets, fills in your cleaning log after each area and reports anything out of place to your cleanroom manager the same shift.
Static-sensitive areas and the floor underfoot
Electronics areas add static to the list. The ESD Association’s figures show that walking across vinyl tile can build about 12,000 volts at 10 to 25% relative humidity and about 250 volts at 65 to 90%, and walking across carpet about 35,000 and 1,500 volts. Damage from a discharge can stop a device outright or leave a hidden flaw that shortens its life.
ANSI/ESD S20.20 sets the requirements for an ESD control program, and any area where sensitive items are handled is an ESD protected area. The basic rules are to ground conductors, people included, and to remove or neutralize insulators. ESDA notes that insulative casters and wheels block the path to ground, so which carts and tools enter those areas is your ESD coordinator’s call. A static-control floor is conductive at 1.0 x 10^6 ohms or less to ground or dissipative between that and 1.0 x 10^9 ohms, and it works together with ESD footwear. The floor maker’s and your facility’s instructions decide which cleaner goes on it, and your team runs the resistance checks.
Shift changes, chases and the office wing
Cleanroom zones run on the frequency your cleanroom manager sets, timed around production and shift changes. Corridors and chases can follow their own cycle, and the office wing, break rooms and restrooms get nightly service from our regular routine. A Menlo Park day porter can keep break rooms and restrooms ready between shifts, and post-construction cleaning handles build-out dust in offices and support rooms outside the cleanroom.
A supervisor inspects every area against your protocol and our route, and our crews are background-checked, insured and bonded.
Bring us your protocol
Send your cleanroom protocol and gowning sequence, then walk the fab and its support rooms with us. We will price the plan from the area of each room type, the frequency for each zone, gowning time per entry, the supplies you provide and the hours that fit production. Request a cleanroom cleaning quote.
A few useful answers
Common questions
Who classifies and tests our cleanroom’s air?
Your facility does. The class describes the room’s air, and our crews clean to the protocol that keeps it there.
Will cleaners bring their own products into our fab?
Only what your protocol lists goes through the door. Crews use your agent, your wipes and tools dedicated to the cleanroom.
How do your cleaners keep from adding particles during a visit?
They gown in your posted order, move slowly, slide nothing across surfaces and plan each entry to finish a full zone.
Who chooses the cleaner for our static-dissipative floor?
The floor maker’s instructions and your facility do. We use the product they name, and your team runs the resistance checks.
Can the gowning room and corridors run on a different schedule from the bays?
Yes. Each zone keeps the frequency your cleanroom manager sets, and offices follow their own nightly routine.

